EN AW-5754 [AlMg3]鋁鎂合金冷拔棒
|
|
|
|
|
|
|
|
|
|
|
|
|
牌號
|
EN AW-5754 [AlMg3]
|
|
|
|
|
|
|
|
|
|
|
|
對應標準
|
DIN EN 754-2-2017
|
|
|
|
|
|
|
|
|
|
|
|
鋁和鋁合金-冷拔棒材和管材-第2部分:機械性能
|
|
|
|
|
|
|
|
|
|
|
|
Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 2: Mechanical properties
|
|
|
|
|
|
|
|
|
|
|
|
歸類
|
鋁及鋁合金
|
|
|
|
|
|
|
|
|
|
|
|
標簽
|
鋁鎂合金
|
|
|
|
|
|
|
|
|
|
|
|
EN AW-5754 [Al Mg3] 化學元素成分含量(%)
|
|
|
|
|
|
|
|
|
|
|
|
|
成分
|
Fe
|
Si
|
Be *
|
Mn
|
Cr
|
Cu
|
Ti
|
Zn
|
Mg
|
其他單個
|
其他合計
|
更多
|
最小值
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
2.6
|
-
|
-
|
Al:余量; Mn+Cr:0.1~0.6
|
最大值
|
0.4
|
0.4
|
0.0003
|
0.5
|
0.3
|
0.1
|
0.15
|
0.2
|
3.6
|
0.05
|
0.15
|
其他單個或其他合計化學成分包括表中未值的化學成分。只有在假定存在或在常規分析中,且有跡象表明其成分將超過規定值的情況下,才應進行分析。
|
|
|
|
|
|
|
|
|
|
|
|
|
化學成分見DIN EN 573-3
|
|
|
|
|
|
|
|
|
|
|
|
|
*僅用于焊條、焊絲。
|
|
|
|
|
|
|
|
|
|
|
|
|
EN AW-5754 [Al Mg3] 機械性能
|
|
|
|
|
|
|
|
|
|
|
|
|
條件
|
熱處理或狀態
|
抗拉強度
|
屈服點
|
斷后伸長率或延伸率
|
硬度
|
|
|
|
|
|
|
|
σb
|
σs
|
δ
|
HBW
|
|
|
|
|
|
|
|
Mpa
|
Mpa
|
%
|
|
|
|
|
|
|
|
|
冷拉棒材; d≤80,s≤60
|
O,H111
|
180~250
|
≥80
|
≥16(A);
|
45
|
|
|
|
|
|
|
|
≥14(A50)
|
|
|
|
|
|
|
|
冷拉棒材; d≤25
|
應變-硬化- 1/2 硬(H14);
|
240~290
|
≥180
|
≥4(A);
|
75
|
|
|
|
|
|
|
|
應變-硬化+不完全退火-1/2硬(H24);
|
≥3(A50)
|
|
|
|
|
|
|
|
應變-硬化+穩化-1/2硬(H34)
|
|
|
|
|
|
|
|
|
冷拉棒材; d≤10
|
應變-硬化- 4/4 硬(H18);
|
≥280
|
≥240
|
≥3(A);
|
88
|
|
|
|
|
|
|
|
應變-硬化+不完全退火-4/4硬(H28);
|
≥2(A50)
|
|
|
|
|
|
|
|
應變-硬化+穩化-4/4硬(H38)
|
|
|
|
|
|
|
|
|
冷拔管材; t≤20
|
O,H111
|
180~250
|
≥80
|
≥16(A);
|
45
|
|
|
|
|
|
|
|
≥14(A50)
|
|
|
|
|
|
|
|
冷拔管材; t≤10
|
應變-硬化- 1/2 硬(H14);
|
240~290
|
≥180
|
≥4(A);
|
75
|
|
|
|
|
|
|
|
應變-硬化+不完全退火-1/2硬(H24);
|
≥3(A50)
|
|
|
|
|
|
|
|
應變-硬化+穩化-1/2硬(H34)
|
|
|
|
|
|
|
|
|
冷拔管材; t≤3
|
應變-硬化- 4/4 硬(H18);
|
≥280
|
≥240
|
≥3(A);
|
88
|
|
|
|
|
|
|
|
應變-硬化+不完全退火-4/4硬(H28);
|
≥2(A50)
|
|
|
|
|
|
|
|
應變-硬化+穩化-4/4硬(H38)
|
|
|
|
|
|
|
|
|
①d=圓棒直徑;s=方、六角棒材截面寬度,矩形棒材的厚度;t=管材壁厚;單位/mm
|
|
|
|
|
|
|
|
|
|
|
|
|
②A、A50-標距
|
|
|
|
|
|
|
|
|
|
|
|
|
? O-退火
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|